Personal tools
You are here: Home → Fedora Mobile → Wireless → Broadcom b43/b43legacy Wireless Support in Fedora
 

Broadcom b43/b43legacy Wireless Support in Fedora

by daMaestro — last modified Aug 15, 2008 12:40 PM
Contributors: Sonar_Guy
— filed under:

A Linux driver for the Broadcom b43 wireless chips. Broadcom never released details about these chips so this driver is based upon reverse engineered specifications.

Requirements

  1. Read our Getting Started with Wireless Guide.
  2. Supported Broadcom hardware. (See this page to see if your device is supported. If you have a BCM4312 check this page.)
  3. Fedora 8 - kernel 2.6.23.15+ with b43-fwcutter 011+
    Note: This might still work in Fedora 7 with a proper kernel.
  4. Existing connection to the Internet. For example, wired internet.
  5. You must have an updated system:
    1. Open a terminal

    2. Run a yum update:

      3. su -c 'yum update'

Doing the Work

  1. Open a terminal .
  2. Install the b43-fwcutter packages:
    3. su -c 'yum install b43-fwcutter'
  3. Check what firmware your card needs:
    dmesg|grep b43

    You will see something like the following with hints on what firmware you need to use:

    b43-phy0 ERROR: Firmware file "b43/ucode5.fw" no found or load failed.
b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
  4. Download the correct firmware for your device from here or select the correct firmware from the following links:

    For b43, download this firmware version 4 and untar it:

    For b43legacy,  download Version 3 firmware:

  5. Extract the firmware:

    For b43:
    su -l -c 'b43-fwcutter -w /lib/firmware /path/to/broadcom-wl-4.150.10.5/driver/wl_apsta_mimo.o'

    For b43legacy:

    su -l -c 'b43-fwcutter -w /lib/firmware /path/to/wl_apsta-3.130.20.0.o'

    For bcm43xx:

    bcm43xx support is outside the scope of this howto. Please read the linux wireless howto for bcm43xx support.

  6. Optional: Enable NetworkManager for managing this device (very recommended!)
  7. Alias the correct module to your wlan0 device:

    For b43:
     
    su -c 'echo "alias wlan0 b43" >> /etc/modprobe.conf'

    For b43legacy:

    su -c 'echo "alias wlan0 b43legacy" >> /etc/modprobe.conf'
  8. With some devices, system-config-network will need to be run:
    su -l -c 'system-config-network'
    Select: New → Wireless → Broadcom Device (should be wlan0)
    Then: Select options suitable for your network configuration. We recommend using NetworkManager and setting the device to not start on boot.
  9. Now, reload the driver:

    For b43:
    su -l -c 'rmmod b43 && modprobe b43'
    For b43legacy:
    su -l -c 'rmmod b43legacy && modprobe b43legacy'
  10. If the reload fails to get your device working correctly, just reboot:
    su -c 'reboot'

Troubleshooting

How to test

Open a terminal.

Ping yahoo: (or any host)
ping yahoo.com

Results similar to the ones below should be displayed:

PING yahoo.com (216.109.112.135) 56(84) bytes of data.
64 bytes from w2.rc.vip.dcn.yahoo.com (216.109.112.135): icmp_seq=0 ttl=53 time=274 ms
[...]

Common problems and fixes

Check irc.freenode.net #bcm-users for any issues experienced with this driver.

More Information

Disclaimer

We test this stuff on our own machines, really we do. But you may run into problems, if you do, come to #fedora on irc.freenode.net

Added Reading

Document Actions

Issues between b43-fwcutter and bcm43xx-fwcutter

Posted by Andres Villarreal at Dec 14, 2007 09:07 PM
I followed the above instructions exactly but they did not work (I use Fedora 7 with 2.6.23.8-34.fc7 kernel and a Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)).

According to these instructions I saw (with lsmod) that I have the b43 module and should have used the b43-fwcutter.

Instead, after several failures, I used the bcm43xx-fwcutter and it worked like a charm.

The difference is that the b43-fwcutter creates a folder called b43 and puts some drivers in it, while bcm43xx-fwcutter creates some files called bcm43xx-* directly in /lib/firmware. My installation requires the latter.

If you are having the same problem as I had, you can see the kernel log (/var/log/messages) and find that when you try to activate your WiFi (with "ifconfig wlan0 up", for example) a message appears like the following:
 

     firmware_helper[3548]: Loading of /lib/firmware/bcm43xx_microcode5.fw for b43 driver failed: No such file or directory
      kernel: b43-phy0 ERROR: Microcode "bcm43xx_microcode5.fw" not available or load failed.


Finally, you should remove the files that either fwcutter creates between tests, or you might get additional strange error messages.

HP NX9105 & BCM4306

Posted by Mike . at Jan 01, 2008 06:02 PM
Ive tried variations on the above instructions with quite a few head scratching moments, the bcm4306 you would think is the 43xx? nope its a b43 so basically for the NX9105, the b43-fwcutter -w /lib/firmware wl-apsta.o seems to work. the modprobe.conf has the 'alias wlan0 b43'

Thanks!

Posted by Andrew Okerstrom at Mar 20, 2008 12:31 AM
This seems to be the only way to get the 4311 card working on my dell inspiron 1720. i've used this method several times and it works like a charm! thanks!

Thanks for this howto

Posted by sophosrex at Jul 02, 2008 12:40 PM
Thanks to whoever wrote this. After much googling this howto worked like a charm on my dell 300M with b43legacy wireless nic

Thanks again

Wireless stopped working

Posted by unset at Jul 05, 2008 06:27 PM
I have a Linksys wireless card with the broadcom 4306 chipset and I'm running Fedora 8. I used the procedure on this page to get the card working about 5 months ago and it's worked flawlessly until a few days ago, but I can no longer connect to my network. dmesg gives me a message saying that I'm using old firmware and must go to http://linuxwireless.org/[…]/b43#devicefirmware and download the latest firmware (version 4). I did this and it still doesn't work. I then followed the procedure on this page, because this page has a more recent version of the firmware, (broadcom-wl-4.150.10.5 as opposed to broadcom-wl-4.80.53.0) but still no joy.

Not sure what the problem is because my card appears to be working, it can see the network in the Wireless Assistent, but it will not connect to it.

Has anyone else had this problem? Could it be a recent Fedora update that has caused the problem and how can I remove the latest updates to check this? Any help would be appreciated. Thanks.

John
Log in


Forgot your password?
New user?